Car Mechanic Simulator 2014: Order 74 - Olsen Grand

CAR: Olsen Grand

TARGETS:

• Replace or repair all worn out parts

REWARD: 7000 USD

PARTS:

• Exhaust Mainfold V6 - 1300 USD
• Catalytic Converter V6 - 1400 USD
• Exhaust Pipe A V6 - 100 USD
• Muffler V6 Middle - 600 USD
• Muffler V6 Rear-Left - 450 USD
• Clutch Friction Plate - 500 USD
• Clutch Pressure Plate - 300 USD
• Clutch Release Bearing - 100 USD

Customer orders you to repair two subsystems - clutch and exhaust - and to change oil. Perform all necessary tests (Diagnostic Path Test, Test Drive) and turn on the Show parts conditions mode. Use the car lifter and take a look on the exhaust. These parts are designed for replace:

• Exhaust Mainfold V6
• Catalytic Converter V6
• Exhaust Pipe V6 A
• Muffler V6 Middle
• Muffler V6 Rear-Left

Prepare new parts and start replacing:

• Remove Muffler V6 Rear-Left and Muffler V6 Rear-Right.
• Remove Muffler V6 Middle.
• Twist off Exhaust Pipe V6 A.
• Remove Catalytic Converter V6.
• Twist off Exhaust Pipe V6 B.
• Lower the car with the Car Lifter and go to the Engine - inspect view mode.
• Twist off Exhaust Manifold V6 and assemble a new model.
• Screw Exhaust Pipe V6 B.
• Assemble new Catalytic Converter V6.
• Screw new Exhaust Pipe V6 A.
• Assemble new Muffler V6 Middle.
• Assemble new Muffler V6 Rear-Left and old Muffler V6 Rear-Right.

You need to disassemble the entire exhaust in order to change the exhaust manifold.

In the second part of the order you will take care of the clutch. Following parts are designed for change:

• Clutch Friction Plate
• Clutch Pressure Plate
• Clutch Release Bearing

Prepare new elements and perform the replacement:

• Go to the Wheel - inspect view mode.
• Turn on the Disassemble Mode.
• Twist off Olsen Grand Rear Left Wheel.
• Twist off Drive Axle Left.

Work with mufflers isn't very comfortable.

Do the same with the rear right wheel and both front wheels. Then:

• Use the Car Lifter and go to the view of the rear chassis with the Undercarriage - inspect option.
• Remove Axle Differential.
• Remove Drive Shaft.
• Lower the car with the Car Lifter and go to the Engine - inspect view mode.
• Twist off Starter V6.
• Disassemble Gearbox V6.
• Remove Clutch Release Bearing.
• Remove Clutch Pressure Plate.
• Remove Clutch Friction Plate and assemble a new part.
• Assemble new Clutch Release Bearing.
• Assemble new Clutch Pressure Plate.
• Assemble Gearbox V6, Starter V6, Drive Shaft, Axle Differential and assemble all twisted off Drive Axles with Vulcan Spectre Wheels.

In the end you have to change oil. Use the Car Lifter and go to the view of the engine from below with the Engine - inspect option. Then:

1. Find Oil Pan located on the bottom of the engine.
2. Find Oil Drain Plug, twist it off and flush the old oil.
3. Lower the car with the Car Lifter and go to the Engine - inspect view mode.
4. Twist off Engine Oil Fill Plug.
5. Click on the oil jerrycan and pour the oil to the engine for a few seconds.
6. Put out Oil Dipstick and check level of oil - point that connects gold and silver field should be as close to the scale's middle as possible.

Car Mechanic Simulator 2014

January 24, 2014

Rate It!

• Overview
• Guide